PE-PJ-005 PowerJet Fuel Controller by Procom – ElectroSport
ELECTRICAL PARTS FOR POWERSPORTS
Cart 0
PE-PJ-005 PowerJet Fuel Controller

PE-PJ-005 PowerJet Fuel Controller

$ 129.00

Most fuel injected engines run very lean and this is fine except for when demanding maximum power output on the track, especially when you have sport exhausts installed. Being able to simply adjust the fuel/air ratio in those conditions would be wonderful wouldn't it?

The PowerJet Fuel Controller allows just that! You can adjust the fuel map from -4% to +10% by selecting one of the 10 settings. We even incorporated a stock setting which means no change compared to stock.

Our PowerJet is a simple yet complicated device. It measures the outside air temperature very close to where the stock sensor is located, and adjusts the signal from the OEM air temperature sensor to the ECU to make use of the built in Air Temperature Correction factor that is built into every stock ECU.

What this accomplishes is that the ECU is told that the intake air is a little cooler than it is, and the ECU will respond by injecting a fraction more fuel depending on the PowerJet setting. You as a rider will notice a substantially improved engine response when you twist the throttle.

The neat thing is that when under constant load (constant speed) the oxygen sensor in the exhaust will make the ECU correct the fuel/air ratio back to stock! However, as soon as the system notices an increase in power it switches from closed loop (oxygen sensor feedback) back to open loop (no feedback) and will correct the fuel/air ratio by the amount you selected on the PowerJet.

PowerJet can be easily installed by plugging it in between the stock AIT sensor which is usually located somewhere on the airbox and the bike's wiring harness. Each PowerJet comes with the exact plug in connectors and installation will normally only take a few minutes. Finding the air temperature sensor usually takes more time than plugging in the PowerJet.

You can leave the PowerJet sitting under the bodywork somewhere as it is designed to be rugged and waterproof. After figuring out what setting works best with your specific engine/exhaust/intake combination you typically do not need to adjust it any more.

PowerJet comes with a full one year warranty.


This product is known to fit:
2001 PIAGGIO 500 X9
2002 PIAGGIO 500 Beverly
2002 PIAGGIO 500 X9
2003 GILERA Nexus 500
2003 PIAGGIO 500 Beverly
2003 PIAGGIO 500 X9 Evolution
2004 GILERA Nexus 500
2004 MALAGUTI SpiderMax GT 500cc / SR500
2004 PIAGGIO 500 Beverly
2004 PIAGGIO 500 X9 Evolution
2005 GILERA Nexus 500
2005 MALAGUTI SpiderMax GT 500cc / SR500
2005 PIAGGIO 500 Beverly
2005 PIAGGIO 500 X9 Evolution
2006 MALAGUTI SpiderMax GT 500cc / SR500
2006 PIAGGIO 400 Beverly
2006 PIAGGIO 400 X8 Euro3
2006 PIAGGIO 500 Beverly
2006 PIAGGIO 500 Beverly i.e. E3 / + Sport
2006 PIAGGIO 500 X9 Evolution
2007 APRILIA Scarabeo 500ie
2007 MALAGUTI Password 250
2007 MALAGUTI SpiderMax GT 500cc / SR500
2007 PIAGGIO 400 Beverly
2007 PIAGGIO 400 X Evo Euro 3
2007 PIAGGIO 400 X8 Euro3
2007 PIAGGIO 500 Beverly Cruiser E3
2007 PIAGGIO 500 Beverly i.e. E3 / + Sport
2007 PIAGGIO 500 X9 Evolution
2008 APRILIA Scarabeo 500 Light
2008 APRILIA Scarabeo 500ie
2008 MALAGUTI Password 250
2008 MALAGUTI SpiderMax GT 500cc / SR500
2008 PIAGGIO 400 X Evo Euro 3
2008 PIAGGIO 400 X8 Euro3
2008 PIAGGIO 500 Beverly Cruiser E3
2008 PIAGGIO 500 Beverly i.e. E3 / + Sport
2009 APRILIA Scarabeo 500 Light
2009 APRILIA Scarabeo 500ie
2009 MALAGUTI SpiderMax GT 500cc / SR500
2009 PIAGGIO 400 X Evo Euro 3
2009 PIAGGIO 500 Beverly Cruiser E3
2010 APRILIA Scarabeo 500 Light
2010 APRILIA Scarabeo 500ie
2011 APRILIA Scarabeo 500 Light
2011 MALAGUTI Password 250
2012 APRILIA Scarabeo 500 Light
2012 MALAGUTI Password 250
2013 APRILIA Scarabeo 500 Light